THERMADOR Error Code E9
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E9 | Turn the clock selector knob to OFF Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window. | Latch switch problems |
The control continuously keeps an eye on system specifications for control as well as stove failures and reports a mistake code when a system trouble is detected. The control makes use of the ovens blue “on light” and also oven “home heating light” to report a discovered mistake code. The control will certainly remain to blink the lights in the appropriate series as long as the mistake exists.
Discovery of a fault does not prevent the capability of the control to remain to work if the mistake is not essential for the desired procedure. For instance: If the variety door latch is inoperative, the variety will remain to cook because the fault would only prevent the variety from self-cleaning.
HOW TO ANALYZE CODES
When a mistake occurs, the control will blink the blue stove “on light” and the Blue “heating light” sequentially to indicate the mistake. The mistake codes have 2 numbers, these numbers are interpreted by the variety of times the lights flash. The stove “on light” will blink showing the first number, as well as the “heating light” will certainly blink suggesting the second number.
INSTANCE:
Mistake E9 is … No Air conditioning Followers. The code is 43. The stove “on light” will flash four times, then the “home heating light” will certainly blink 3 times, then pause. The series will certainly then repeat as long as the fault is present.
ERROR CODES FOR OVENS WITH DREEFS CONTROL
The adhering to graph reveals the mistake codes that can be presented in the Oven/Selector window during specific oven malfunctions. Several of the mistake messages can be gotten rid of by executing the adhering to steps:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |