THERMADOR Error Code E7
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E7 | Turns heat off on failed oven only, micro not affected. Cleared with a mode change. | Illegal temp display turn off and retry |
The control continuously checks system specifications for control and stove failings and reports a mistake code when a system issue is found. The control utilizes the stoves blue “on light” and also oven “home heating light” to report a discovered mistake code. The control will continue to flash the lights in the ideal series as long as the fault exists.
Discovery of a mistake does not impede the capability of the control to remain to function if the fault is not important for the desired operation. For instance: If the variety door lock is defective, the range will certainly continue to prepare considering that the fault would just avoid the range from self-cleaning.
HOW TO INTERPRET CODES
When a fault happens, the control will blink the blue stove “on light” and the Blue “home heating light” sequentially to suggest the fault. The fault codes have 2 numbers, these numbers are translated by the number of times the lights flash. The stove “on light” will certainly blink suggesting the initial number, and the “heating light” will certainly blink showing the second number.
INSTANCE:
Error E9 is … No Cooling Fans. The code is 43. The stove “on light” will certainly flash four times, then the “heating light” will flash three times, after that time out. The series will certainly then duplicate as long as the mistake exists.
ERROR CODES FOR STOVES WITH DREEFS CONTROL
The complying with chart reveals the mistake codes that can be displayed in the Oven/Selector home window during specific stove breakdowns. A few of the mistake messages can be cleared by performing the following actions:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |