THERMADOR Error Code E2
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E2 | Turns all heat and micro off. Clears when oven temp drops below runaway temp and selector is off. | Repair the electronic rannge control (also called clock ERC) |
The control constantly checks system parameters for control and also oven failures and also reports a mistake code when a system issue is spotted. The control utilizes the stoves blue “on light” and also oven “heating light” to report an identified mistake code. The control will certainly remain to flash the lights in the proper sequence as long as the fault exists.
Discovery of a mistake does not prevent the capability of the control to remain to operate if the mistake is not vital for the desired operation. For instance: If the range door latch is faulty, the variety will remain to prepare considering that the mistake would just avoid the variety from self-cleaning.
HOW TO TRANSLATE CODES
When a mistake occurs, the control will flash heaven oven “on light” as well as heaven “heating light” sequentially to indicate the fault. The mistake codes have two numbers, these numbers are interpreted by the number of times the lights blink. The stove “on light” will certainly flash showing the very first number, as well as the “heating light” will flash showing the second number.
EXAMPLE:
Mistake E9 is … No Cooling Fans. The code is 43. The stove “on light” will certainly blink four times, after that the “heating light” will certainly flash 3 times, after that time out. The series will certainly after that duplicate as long as the mistake is present.
MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The following chart shows the error codes that can be shown in the Oven/Selector home window during certain stove malfunctions. Some of the error messages can be gotten rid of by executing the following steps:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |