THERMADOR Error Code E15
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E15 | Turns all heat off, micro not affected. Error will remain in display until repaired and powered up. No error tones. | Repair the electronic range control (also called clock or ERC) |
The control continuously checks system specifications for control as well as stove failures and reports a mistake code when a system problem is detected. The control makes use of the ovens blue “on light” and oven “heating light” to report a detected mistake code. The control will certainly remain to flash the lights in the ideal sequence as long as the mistake exists.
Detection of a mistake does not prevent the capability of the control to remain to work if the mistake is not crucial for the designated procedure. For example: If the range door latch is faulty, the range will continue to cook considering that the fault would only protect against the variety from self-cleaning.
HOW TO TRANSLATE CODES
When a fault occurs, the control will blink heaven oven “on light” and heaven “home heating light” sequentially to show the fault. The mistake codes have 2 numbers, these numbers are interpreted by the variety of times the lights blink. The stove “on light” will blink suggesting the initial number, and the “home heating light” will flash suggesting the 2nd number.
INSTANCE:
Error E9 is … No Cooling Fans. The code is 43. The stove “on light” will flash four times, then the “home heating light” will flash three times, then time out. The series will certainly after that duplicate as long as the mistake exists.
MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The adhering to graph reveals the mistake codes that can be displayed in the Oven/Selector window during certain oven malfunctions. Several of the error messages can be gotten rid of by executing the adhering to steps:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |