THERMADOR Error Code E11
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E11 | Turns heat off on failed oven only, micro not affected. Tweaking clears to “—” for retry. Turns heat off on failed oven only, micro not affected. | CT oven; latch switch problem |
The control constantly keeps track of system parameters for control as well as stove failings and also reports a mistake code when a system problem is discovered. The control utilizes the stoves blue “on light” and also oven “heating light” to report an identified mistake code. The control will certainly continue to blink the lights in the appropriate sequence as long as the fault exists.
Discovery of a mistake does not prevent the capacity of the control to remain to operate if the fault is not crucial for the desired procedure. For instance: If the array door latch is inoperative, the range will remain to cook given that the fault would just protect against the variety from self-cleaning.
HOW TO ANALYZE CODES
When a mistake occurs, the control will flash the blue stove “on light” and also the Blue “heating light” sequentially to suggest the mistake. The mistake codes have two numbers, these numbers are interpreted by the number of times the lights flash. The oven “on light” will certainly blink suggesting the first number, and the “home heating light” will blink showing the second number.
EXAMPLE:
Mistake E9 is … No Air conditioning Fans. The code is 43. The oven “on light” will certainly blink 4 times, then the “heating light” will flash three times, after that pause. The sequence will after that duplicate as long as the fault exists.
ERROR CODES FOR OVENS WITH DREEFS CONTROL
The complying with graph shows the error codes that can be presented in the Oven/Selector home window during details oven breakdowns. A few of the mistake messages can be gotten rid of by doing the following steps:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |