THERMADOR Error Code E10
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E10 | Turns all heat off, micro not affected. Error will remain in display until repaired and powered up. No error tones. | Repair the electronic range control (also called clock or ERC) |
The control continually keeps an eye on system parameters for control and oven failures and reports a mistake code when a system issue is discovered. The control utilizes the stoves blue “on light” and also oven “heating light” to report a found mistake code. The control will continue to flash the lights in the ideal sequence as long as the mistake exists.
Detection of a mistake does not hinder the ability of the control to continue to work if the mistake is not vital for the intended operation. For example: If the variety door latch is inoperative, the variety will remain to cook since the fault would just stop the range from self-cleaning.
HOW TO TRANSLATE CODES
When a fault happens, the control will certainly flash the blue oven “on light” as well as heaven “home heating light” sequentially to suggest the mistake. The fault codes have two numbers, these numbers are translated by the variety of times the lights flash. The stove “on light” will certainly flash indicating the initial number, and also the “home heating light” will certainly blink suggesting the 2nd number.
INSTANCE:
Error E9 is … No Cooling Fans. The code is 43. The stove “on light” will certainly blink 4 times, then the “home heating light” will flash three times, after that pause. The sequence will certainly after that duplicate as long as the fault exists.
ERROR CODES FOR OVENS WITH DREEFS CONTROL
The adhering to chart shows the error codes that can be presented in the Oven/Selector window during details stove malfunctions. Some of the mistake messages can be cleared by executing the complying with actions:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |