Bosch washing machines are considered to be among the most reputable and useful worldwide. Purchasers pay the unique focus to Bosch Vision 300 series washer. The crucial benefits that identify the brand name’s tool:
a high level of power, which satisfies the demands of a huge family;
superb power efficiency signs, which enable conserving both electrical power and also water;
silence during work that is specifically crucial in an apartment;
exceptional cleansing performance. Additionally, there is a program that removes bacteria with practically 100% performance;
favorable customer responses.
Yet even such a vast collection of merits can not conserve the device from malfunctions and also malfunctions. Bosch Vision 300 collection reveals error codes in various scenarios. The problems relate to:
the way a user operates the home appliance;
failing of components as well as parts.
If you don’t recognize what a particular code implies, check the table below. Locate the mistake, which your washing machine reveals on the screen. Having determined the details cause of the code occurrence, proceed to the next job. You need to make a decision whether you need a specialist assistance from washing machine specialist or otherwise. Perhaps, you can deal with the error independently by adjusting the cleaning procedure criteria.
Problem | Possible cause | Remedial action |
Dryer does not start. “Start/Pause” indicator light does not illuminate. | Main plug not inserted at all or not inserted correctly. | Insert main plug correctly. |
A fuse or circuit breaker has tripped. | Replace fuse or reset circuit breaker. | |
“Start/Pause” button not pressed. | Press “Start/Pause” button. | |
No program selected. | Select program. | |
Door not closed. | Close door. | |
Ambient temperature below 41 °F (5 °C.) | Increase room temperature. | |
Laundry is wet after drying. | The shut-off valve is closed. | Open the shut-off valve. |
Cycle has been interrupted. A warning signal is emitted and the display shows “CLn”. | Lint filter dirty. | Clean the lint filter. Switch the dryer off/switch on again. If this does not clear the error code |
Cycle has been interrupted. A warning signal is emitted and the display shows “E:12” | Exhaust air duct is blocked or too long. | Clean exhaust air duct. Reduce exhaust air duct to maximum length. Switch the dryer off/switch on again. |
Fault in program sequence or malfunction. | Switch off dryer, leave to cool down for 30 min, switch on again. | |
Restart program. | ||
The room/cabinet is not adequately ventilated. | Provide an adequate supply of fresh air. Switch off/switch on again. | |
Degree of drying has not been reached or the drying time is too long. Display may indicate E:03. | Moisture sensor dirty. | Clean moisture sensor. Switch the dryer off/switch on again. |
Exhaust air duct is blocked or is too long. | Clean exhaust air duct. Reduce exhaust air duct to maximum length. Switch the dryer off/switch on again. | |
Lint filter dirty. | Clean filter. Switch the dryer off/switch on again. | |
Laundry was too wet. | Spin laundry at higher speed in the washing machine. Switch the dryer off/switch on again. | |
Unsuitable program selected. | Select program with aid of the program selection table. Switch the dryer off/switch on again. | |
Maximum drying time was exceeded. | Clean lint filter. Check exhaust air duct. Spin laundry at a higher speed in your washer. | |
Motor limit temperature was exceeded. | Switch off dryer, leave to cool down for 30 min. Switch on again. Start program. | |
Degree of dryness not correctly set. | 800 Series, Change settings for degree of dryness. | |
Drum light does not function. | No program selected. | Select program. |
Light bulb defective, light bulb burned out. | Replace burned out bulb and reinstall the cover | |
No power supply. | Check power supply. | |
Light bulb is loose. | Remove the bulb cover and if bulb is loose, tighten bulb. Reinstall the cover. | |
“Start/Pause” indicator light does not illuminate. “Wrinkle Block®/Finished” indicator lights. The display shows “OOO”. | Fault in program sequence or malfunction. | Switch off dryer, leave to cool down for 30 min, switch on again. Restart program. |
Lint filter LED is blinking after the lint filter has been cleaned | Blinking of lint filter LED is not an indication of a problem. It is used only as a reminder. | No action required. Light will stop blinking. |
Display shows “—”. | Laundry detected in drum during wool program (laundry not on rack). | Place laundry on dryer rack. Restart program. |
Unusual noise: thumping sound | Drum suspension rollers need time to warm up. | No action required. As suspension system rollers warm up thumping will decrease and should stop within 2 to 3 minutes of dryer use. |
Unusual noise: Steady vibration, rocking of the dryer | Dryer is not level. | Level the dryer |
Unusual noise: Rhythmic vibration | Laundry balled up causing load to bounce. | Stop dryer, separate load items, restart dryer. |
Water is not sprayed into the unit during Steam cycles | Water tap(s) not turned on. | Turn on water tap. |
Nozzle does not spray water adequately. | Wipe the outside of the nozzle with a cloth moistened with vinegar. If this does not restore the nozzle to spraying, see “Blocked nozzle” remedial action below. | |
Blocked nozzle | Remove the nozzle using a 7/16 inch (11 mm) socket wrench. Place the nozzle into a container filled with enough white vinegar to cover the nozzle. Allow the nozzle to soak for five minutes, then scrub the nozzle tip gently with a toothbrush to remove residue. Rinse the nozzle and reinsert it back into the dryer and hand tighten, then tighten 1 additional turn with the wrench. | |
LED or button illuminated on control panel when Cycle Selector is turned to “Off” position | Fault condition | Turn off the circuit breaker |